This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Next revision Both sides next revision | ||
projects_for_the_coverstitch_machine [2017/10/09 14:43] 192.168.1.194 |
projects_for_the_coverstitch_machine [2017/10/09 15:06] 192.168.1.194 |
||
---|---|---|---|
Line 235: | Line 235: | ||
{{:projects:reverse_top_stitching_needle_positioning.jpg?800|}} | {{:projects:reverse_top_stitching_needle_positioning.jpg?800|}} | ||
- | The right needle penetrates just a little to the right of the overlocking seam thread | + | The right needle penetrates just a little to the right of the left overlocking needle thread. |
{{:projects:seam_line_completely_covered_by_reverse_stitches.jpg?800|}} | {{:projects:seam_line_completely_covered_by_reverse_stitches.jpg?800|}} | ||
+ | |||
+ | The result is a seam line that is completely covered by the decorative coverstitch looper thread. | ||
+ | And in case you ever wondered about adult raglan sleeves passing through the Babylock harp?? They do!! | ||
+ | |||
{{:projects:babylock_with_adult_raglan_sleeve_through_narrow_harp.jpg?800|}} | {{:projects:babylock_with_adult_raglan_sleeve_through_narrow_harp.jpg?800|}} | ||
+ | |||
+ | Next the side seams were closed and notice that it is important to accurately match top stitching lines for a continuous effect. | ||
+ | |||
+ | {{:projects:when_the_seams_match.jpg?800|}} | ||
+ | |||
+ | Here with sleeve bands and top stitching | ||
+ | |||
+ | {{:projects:top_stitching_the_sleeve_bands.jpg?800|}} | ||
+ | |||
+ | Preparing the hem | ||
+ | |||
{{:projects:pressing_the_hem.jpg?800|}} | {{:projects:pressing_the_hem.jpg?800|}} | ||
+ | |||
+ | The finished hem | ||
+ | |||
{{:projects:reverse_stitched_hem.jpg?800|}} | {{:projects:reverse_stitched_hem.jpg?800|}} | ||
+ | |||
+ | Applying double sided tape to the front edges to position the zipper | ||
+ | |||
{{:projects:preparing_double_sided_tape_for_zipper.jpg?800|}} | {{:projects:preparing_double_sided_tape_for_zipper.jpg?800|}} | ||
+ | |||
+ | Attaching the zipper with a regular sewing machine | ||
+ | |||
{{:projects:attach_zipper.jpg?800|}} | {{:projects:attach_zipper.jpg?800|}} | ||
+ | |||
+ | When folding the zipper, I used a small piece of double sided tap to make sure the horizontal seam lines would match | ||
+ | |||
+ | {{:projects:avoid_zipper_slipping_with_tape.jpg?800|}} | ||
+ | |||
+ | Looks OK? | ||
+ | |||
{{:projects:position_zipper_for_matching_seams.jpg?800|}} | {{:projects:position_zipper_for_matching_seams.jpg?800|}} | ||
+ | |||
+ | The zipper should be longer than the project so that a few teeth can be removed and the zipper band can be trimmed as needed. | ||
+ | |||
{{:projects:use_larger_zipper_and_trim.jpg?800|}} | {{:projects:use_larger_zipper_and_trim.jpg?800|}} | ||
- | {{:projects:avoid_zipper_slipping_with_tape.jpg?800|}} | + | |
+ | Top stitching as close to the teeth as possible | ||
{{:projects:top_stitch_zipper_as_close_to_teeth_as_possible.jpg?800|}} | {{:projects:top_stitch_zipper_as_close_to_teeth_as_possible.jpg?800|}} | ||
+ | |||
+ | And this is what it looks like on the wrong side | ||
+ | |||
{{:projects:zipper_from_the_wrong_side.jpg?800|}} | {{:projects:zipper_from_the_wrong_side.jpg?800|}} | ||
+ | When top stitching the zipper, it is important to keep the layers from shifting so I use a thread ripper to gently press down in front of the sewing foot. | ||
{{:projects:gently_keep_layers_together_while_top_stitching_to_avoid_shifting.jpg?800|}} | {{:projects:gently_keep_layers_together_while_top_stitching_to_avoid_shifting.jpg?800|}} | ||
- | {{:projects:carefully_hand_sew_thread_tails.jpg?800|}} | ||
+ | As I reach the end, I usually turn the wheel by hand to finish the last couple of stitches and the tails need to be secured properly. | ||
- | | + | {{:projects:carefully_hand_sew_thread_tails.jpg?800|}} |
+ | The hood parts were assembled and hemmed. | ||
{{:projects:hemming_the_hood_with_reverse_stitching.jpg?800|}} | {{:projects:hemming_the_hood_with_reverse_stitching.jpg?800|}} | ||
+ | |||
+ | Before turning to the serger, I attached the extremities of the hood with a few stitches to the front of the jacket. | ||
{{:projects:attaching_the_hood_starting_with_a_few_stitches_on_sewing_machine.jpg?800|}} | {{:projects:attaching_the_hood_starting_with_a_few_stitches_on_sewing_machine.jpg?800|}} | ||
+ | |||
+ | And another row of top stitching | ||
+ | |||
{{:projects:trim_the_point_and_carefully_top_stitch_the_hood_close_to_zipper_turn_handwheel_by_hand.jpg?800|}} | {{:projects:trim_the_point_and_carefully_top_stitch_the_hood_close_to_zipper_turn_handwheel_by_hand.jpg?800|}} | ||
+ | |||
+ | When starting on the edge, I always use a hump jumper to help the edge move forward and I hold on to the thread tails to make sure that the stitches start forming right away. | ||
+ | |||
{{:projects:top_stitching_the_hood_starting_on_hump_jumper_hold_the_thread_tails.jpg?800|}} | {{:projects:top_stitching_the_hood_starting_on_hump_jumper_hold_the_thread_tails.jpg?800|}} | ||
+ | |||
+ | Not too bad! | ||
+ | |||
{{:projects:finished_top_stitching_hood.jpg?800|}} | {{:projects:finished_top_stitching_hood.jpg?800|}} | ||
- | {{:projects:when_the_seams_match.jpg?800|}} | + | And TADA...... one more finished jacket. |
- | {{:projects:top_stitching_the_sleeve_bands.jpg?800|}} | + | |
{{:projects:zippered_jacket_finished.jpg?800|}} | {{:projects:zippered_jacket_finished.jpg?800|}} |